Identificador persistente para citar o vincular este elemento: http://hdl.handle.net/10553/128247
Campo DC Valoridioma
dc.contributor.authorSuárez, Luis-
dc.contributor.authorHanna, Paul R.-
dc.contributor.authorOrtega Medina, Zaida Cristina-
dc.contributor.authorBarczewski, Mateusz-
dc.contributor.authorKosmela, Paulina-
dc.contributor.authorMillar, Bronagh-
dc.contributor.authorCunningham, Eoin-
dc.date.accessioned2024-01-08T11:21:33Z-
dc.date.available2024-01-08T11:21:33Z-
dc.date.issued2024-
dc.identifier.issn1544-0478-
dc.identifier.otherWoS-
dc.identifier.urihttp://hdl.handle.net/10553/128247-
dc.description.abstractGiant reed (Arundo donax L.) is a plant species with a high growth rate and low requirements, which makes it particularly interesting for the production of different bioproducts, including natural fibers. This work assesses the use of fibers obtained from reed culms as reinforcement for a high-density polyethylene (HDPE) matrix. Two different lignocellulosic materials were used: i) shredded culms and ii) fibers obtained by culms processing, which have not been reported yet in literature as fillers for thermoplastic materials. A good stress transfer for the fibrous composites was observed, with significant increases in mechanical properties; composites with 20% fiber provided a tensile elastic modulus of almost 1900 MPa (78% increase versus neat HDPE) and a flexural one of 1500 MPa (100% increase), with an improvement of 15% in impact strength. On the other hand, composites with 20% shredded biomass increased by 50% the tensile elastic modulus (reaching 1560 MPa) and the flexural one (up to 1500 MPa), without significant changes in impact strength. The type of filler is more than its ratio; composites containing fibers resulted in a higher performance than the ones with shredded materials due to the higher aspect ratio of fibers.-
dc.languageeng-
dc.relation.ispartofJournal of Natural Fibers-
dc.sourceJournal Of Natural Fibers[ISSN 1544-0478],v. 21 (1), (Diciembre 2024)-
dc.subject331005 Ingeniería de procesos-
dc.subject3312 Tecnología de materiales-
dc.subject.otherArundo donax-
dc.subject.otherGiant reed-
dc.subject.otherBiomass-
dc.subject.otherFibers-
dc.subject.otherComposites-
dc.subject.otherHDPE-
dc.subject.otherCharacterization-
dc.subject.otherInjection molding-
dc.subject.otherHigh-Density Polyethylene-
dc.subject.otherDynamic-Mechanical Properties-
dc.subject.otherSoil-Water Availability-
dc.subject.otherEntanglement Density-
dc.subject.otherPolymer Composites-
dc.titleInfluence of Giant Reed (Arundo Donax L.) Culms Processing Procedure on Physicochemical, Rheological, and Thermomechanical Properties of Polyethylene Composites-
dc.typeinfo:eu-repo/semantics/article-
dc.typeArticle-
dc.identifier.doi10.1080/15440478.2023.2296909-
dc.identifier.isi001137122800001-
dc.identifier.eissn1544-046X-
dc.identifier.issue1-
dc.relation.volume21-
dc.investigacionIngeniería y Arquitectura-
dc.type2Artículo-
dc.contributor.daisngid1638668-
dc.contributor.daisngid22993765-
dc.contributor.daisngid1596698-
dc.contributor.daisngid841180-
dc.contributor.daisngid29903463-
dc.contributor.daisngid12007603-
dc.contributor.daisngid28787051-
dc.description.numberofpages31-
dc.utils.revision-
dc.contributor.wosstandardWOS:Suarez, L-
dc.contributor.wosstandardWOS:Hanna, PR-
dc.contributor.wosstandardWOS:Ortega, Z-
dc.contributor.wosstandardWOS:Barczewski, M-
dc.contributor.wosstandardWOS:Kosmela, P-
dc.contributor.wosstandardWOS:Millar, B-
dc.contributor.wosstandardWOS:Cunningham, E-
dc.date.coverdateDiciembre 2024-
dc.identifier.ulpgc-
dc.contributor.buulpgcBU-ING-
dc.description.sjr0,602-
dc.description.jcr3,5-
dc.description.sjrqQ2-
dc.description.jcrqQ1-
dc.description.scieSCIE-
dc.description.miaricds10,7-
item.grantfulltextopen-
item.fulltextCon texto completo-
crisitem.author.deptGIR Fabricación integrada y avanzada-
crisitem.author.deptDepartamento de Ingeniería Mecánica-
crisitem.author.deptGIR Fabricación integrada y avanzada-
crisitem.author.deptDepartamento de Ingeniería de Procesos-
crisitem.author.orcid0000-0002-6709-1555-
crisitem.author.orcid0000-0002-7112-1067-
crisitem.author.parentorgDepartamento de Ingeniería Mecánica-
crisitem.author.parentorgDepartamento de Ingeniería Mecánica-
crisitem.author.fullNameSuárez García, Luis Adargoma-
crisitem.author.fullNameOrtega Medina, Zaida Cristina-
Colección:Artículos
Adobe PDF (8,74 MB)
Vista resumida

Citas de WEB OF SCIENCETM
Citations

3
actualizado el 24-nov-2024

Visitas

117
actualizado el 31-oct-2024

Descargas

59
actualizado el 31-oct-2024

Google ScholarTM

Verifica

Altmetric


Comparte



Exporta metadatos



Los elementos en ULPGC accedaCRIS están protegidos por derechos de autor con todos los derechos reservados, a menos que se indique lo contrario.