Identificador persistente para citar o vincular este elemento: http://hdl.handle.net/10553/119571
Campo DC Valoridioma
dc.contributor.authorRomero Artiles, Francisco Ramón-
dc.contributor.authorOrtega Medina, Zaida Cristina-
dc.contributor.authorCastellano Vera, Jesica-
dc.contributor.authorBenítez Vega, Antonio Nizardo-
dc.contributor.authorMarrero Alemán, María Dolores-
dc.contributor.authorSuárez García, Luis Adargoma-
dc.date.accessioned2022-12-05T08:48:04Z-
dc.date.available2022-12-05T08:48:04Z-
dc.date.issued2022-
dc.identifier.issn0170-0839-
dc.identifier.otherScopus-
dc.identifier.urihttp://hdl.handle.net/10553/119571-
dc.description.abstractThis paper focuses on the use of castor oil plant (Ricinus communis) as filler in rotomolded parts using polyethylene (PE) and polylactic acid (PLA) as polymer matrixes. The vegetable shredded material was used in 5 and 10% weight following a dry blending procedure and then rotomolded to obtain cube test parts. This material was characterized to determine its chemical composition, thermal stability, and structure. The NaOH-treated material shows reduced hemicellulose content and higher thermal stability. Obtained composite materials were characterized in terms of mechanical (tensile, flexural, and impact) and thermal properties, morphology, and bio-disintegration behavior. The use of Ricinus as filler in rotomolded PE composite decreases, in general terms, mechanical properties of neat PE, while no significant changes in thermal or bio-disintegration properties are found. On the contrary, PLA composites show higher tensile strength and similar Young's modulus than the matrix, although with reduced flexural and impact properties. Alkali-treated Ricinus material produces parts with higher porosity and thus, lower mechanical properties than composites with untreated material. Finally, the incorporation of this vegetal material modifies to a great extent the thermal properties of the PLA matrix. The bio-disintegration rate increases due to the use of fibers, probably because of the higher moisture absorption of composites.-
dc.languageeng-
dc.relationPotencial aprovechamiento de biomasa generada a partir de especies vegetales invasoras de la Macaronesia para uso industrial-
dc.relation.ispartofPolymer Bulletin-
dc.sourcePolymer Bulletin [ISSN 0170-0839], (2022)-
dc.subject3312 Tecnología de materiales-
dc.subject331209 Resistencia de materiales-
dc.subject.otherCastor oil plant-
dc.subject.otherRicinus communis-
dc.subject.otherRotational molding-
dc.subject.otherCharacterization-
dc.subject.otherDisintegration-
dc.subject.otherPLA-
dc.subject.otherPE-
dc.titleUse of Ricinus communis shredded material as filler in rotational molded parts to improve the bio-disintegration behavior-
dc.typeinfo:eu-repo/semantics/article-
dc.identifier.doi10.1007/s00289-022-04593-5-
dc.identifier.scopus85143169225-
dc.contributor.orcid0000-0003-1437-3046-
dc.contributor.orcid0000-0002-7112-1067-
dc.contributor.orcid0000-0002-8805-987X-
dc.contributor.orcid0000-0001-5711-6395-
dc.contributor.orcid0000-0002-9396-1649-
dc.contributor.orcid0000-0002-6709-1555-
dc.contributor.authorscopusid57225138822-
dc.contributor.authorscopusid36241994700-
dc.contributor.authorscopusid57221965221-
dc.contributor.authorscopusid57210096811-
dc.contributor.authorscopusid8372557400-
dc.contributor.authorscopusid7102054991-
dc.identifier.eissn1436-2449-
dc.investigacionIngeniería y Arquitectura-
dc.type2Artículo-
dc.utils.revision-
dc.date.coverdateEnero 2022-
dc.identifier.ulpgc-
dc.contributor.buulpgcBU-ING-
dc.description.sjr0,482-
dc.description.jcr3,2-
dc.description.sjrqQ2-
dc.description.jcrqQ2-
dc.description.scieSCIE-
dc.description.miaricds11,0-
item.fulltextCon texto completo-
item.grantfulltextopen-
crisitem.project.principalinvestigatorMarrero Alemán, María Dolores-
crisitem.author.deptGIR Fabricación integrada y avanzada-
crisitem.author.deptGIR Fabricación integrada y avanzada-
crisitem.author.deptDepartamento de Ingeniería de Procesos-
crisitem.author.deptGIR Fabricación integrada y avanzada-
crisitem.author.deptGIR Fabricación integrada y avanzada-
crisitem.author.deptDepartamento de Ingeniería de Procesos-
crisitem.author.deptGIR Fabricación integrada y avanzada-
crisitem.author.deptDepartamento de Ingeniería Mecánica-
crisitem.author.deptGIR Fabricación integrada y avanzada-
crisitem.author.orcid0000-0003-1437-3046-
crisitem.author.orcid0000-0002-7112-1067-
crisitem.author.orcid0000-0001-5711-6395-
crisitem.author.orcid0000-0002-9396-1649-
crisitem.author.orcid0000-0002-6709-1555-
crisitem.author.parentorgDepartamento de Ingeniería Mecánica-
crisitem.author.parentorgDepartamento de Ingeniería Mecánica-
crisitem.author.parentorgDepartamento de Ingeniería Mecánica-
crisitem.author.parentorgDepartamento de Ingeniería Mecánica-
crisitem.author.parentorgDepartamento de Ingeniería Mecánica-
crisitem.author.parentorgDepartamento de Ingeniería Mecánica-
crisitem.author.fullNameRomero Artiles, Francisco Ramón-
crisitem.author.fullNameOrtega Medina, Zaida Cristina-
crisitem.author.fullNameCastellano Vera, Jesica-
crisitem.author.fullNameBenítez Vega, Antonio Nizardo-
crisitem.author.fullNameMarrero Alemán, María Dolores-
crisitem.author.fullNameSuárez García, Luis Adargoma-
Colección:Artículos
Adobe PDF (4,12 MB)
Vista resumida

Visitas

68
actualizado el 23-mar-2024

Descargas

49
actualizado el 23-mar-2024

Google ScholarTM

Verifica

Altmetric


Comparte



Exporta metadatos



Los elementos en ULPGC accedaCRIS están protegidos por derechos de autor con todos los derechos reservados, a menos que se indique lo contrario.